Quality Dial Torque Wrenches at Great Prices
tinyurl.com – Learn how to purchase the cheapest Online Tools. Batteries & Chargers Buffers & Polishers Combination Sets Drill Bits Corded Drills Cordless Drills Cordless Impact Drivers Cordless Impact Wrenches Grinders Heat Guns Jacks & Stands Joiners Lathes & Accessories…
Titan Technolgies Crab Nut Reaction arm setup. Saves time and effort when installing or removing Crab Nuts from EMD diesels.
TorcUP’s Raptor Pneumatic Torque Wrench withSlider Arm Reaction Fixture. Lightweight, Durable, Balanced. Simple ease of operation. No Hammering. Reduces Risk of Injuries. Simple as pressing a button for fast, safe open and close. Air Motor, no electrical spark. No chance of explosion. The Raptor is ready to accommodate your Torque needs from 120ft/lbs to 6000ft/lbs! Contact TODAY for a FREE onsite Demonstration
TorcUP’s Raptor Pneumatic Torque Wrench with Crabnut Reaction Fixture. Lightweight, Durable, Balanced. Simple ease of operation. No Hammering. Reduces Risk of Injuries. Simple as pressing a button for fast, safe open and close. Air Motor, no electrical spark. No chance of explosion. The Raptor is ready to accommodate your Torque needs from 120ft/lbs to 6000ft/lbs! Contact TODAY for a FREE onsite Demonstration.
TorcUP Alex Tagliani Fazzt Edmonton Indycar 2010 Izod Series Sunday, July 25, Edmonton, AB, City Centre Airport IndyCar 2010 Honda Indy Edmonton -TorcUP Industrial Bolting Tools – www.torcup.com www.torcup.ca www.fazztraceteam.com 2010 IndyCar® (and Design) are registered trademarks of Brickyard Trademarks IZOD is a registered trademark of Phillips-Van Heusen Corporation
I had the brake shoes relined at Auto and Industrial Friction Services, near Bedford, Tel: 01462 834778: www.autoandindustrial.co.uk The original friction material thickness should be 1/4 inch and a heavy duty grade needs to be used due to the weight of the vehicle (~3 ton). The friction material is now bonded, instead of riveted, as is allows for greater wear to be accommodated between relinings. Before reinstalling the brake shoes, wind in the screws in the face of each wheel cylinder piston. This will provide sufficient clearance for the brake drums when sliding them over the new brake shoes. The wheel cylinders were sleeved with stainless steel at: Locke Engineering Thorpe Industrial Estate Eversley Way Egham Surrey TW20 8RG Tel: 01784 438 120 I replaced the metal brake pipes with 1/4″ kunifer tubing. I made them up with new male flare nuts (thread size & pitch: 7/16″x20TPI) for the 1/4″ pipe ends. The standard flare nuts require a 12mm flare nut spanner to remove them. Ordinary spanners, wrenches and mole grips will just chew the nut up and make it more diificult to remove, so it’s best to use the correct tool. I replaced the 12mm nuts with 7/16″ nuts as that is all I could get hold of here in the UK. The cut lengths of kunifer piping required were as follows: Front upper wheel cylinder: 215mm Front lower wheel cylinder: 260mm Rear upper wheel cylinder: 215mm Rear lower wheel cylinder: 290mm Front Axle right brake pipe: 900mm Front Axle left brake pipe: 345mm Back …
www.wigglesworth.com GIDDINGS & LEWIS WINSLO-MATIC HR-947 DRILL SHARPENER NEW 1991 FULLY EQUIPPED Our stock number: 8324 SERIAL ………… 947-00336-91 MODEL ……….. HR NEW IN ………… 1991 SPECIFICATIONS: WINSLOWMATIC MODEL HR DRILL POINT SHARPENER, FULLY EQUIPPED TO PRODUCE BICKFORD AND RACON POINTS ON ALL FRACTION, NUMBER, AND LETTER SIZE DRILLS, FROM 1/8″ (.125) – 1.0″. ALSO PRODUCES CONVENTIONAL AND HELICAL POINTS FROM 90 – 140 DEGREE INCLUDED POINT ANGLE ON ALL FRACTION, NUMBER, AND LETTER SIZE DRILLS FROM 1/16″ (.062) – 1.0″ VOLTAGE 220 3 60 NOTE: The Following Equipment was provided with this unit at the time of purchase This unit is for sale from the original owner. The items listed below are believed to be with the machine, however are subject to verification. The machine is in very nice condition and is available to be inspected underpower. EQUIPPED WITH: INDEX BUSING ASSEMBLIES (1/16″ – 3/4″) DRILL HOLDER ASSEMBLIES (1/16″ – 3/4″) DRILL HOLDER AND COLLETS 49/64″ – 1″ AIR INFEED CONTROL FLOOD COOLANT SYSTEM DRESSER CAMS TO PRODUCE BICKFORD, HELICAL, RACON, & CONVENTIONAL POINTS WORKLIGHT GRINDING WHEEL MOUNTS BALANCING ARBOR ALLEN & SPANNER WRENCHES OPERATION & MAINTENANCE MANUALS MISTKOP / TOP HAT HR 947 MIST COLLECTION SYSTEM DRESSER CAM AND TIMER FOR 60 – 90 DEGREE POINT ANGLES ACCESSORY KIT NO. 5 TO SHARPEN LEFT HAND DRILLS TO .750″ DIAMETER ACCESSORY KIT NO. 9 METRIC BUSHING PLATE ASSEMBLIES ADDITIONAL UN-USED GRINDING WHEELS “AS IS” FOB SALEM …
The new Torque Gun FLIP can run down nuts (on bolts from 3/4″ to 2″ diameter) faster than an impact wrench and accurate like a hydraulic torque wrench. It is the ultimate 2-in-1 for industrial bolting!
TITAN Hydraulic Torque wrench, Size LP-8 with a 3 1/2 link on a pressure vessle for a local NUCLEAR POWER PLANT
Rapid-Torc® is The Expert for Industrial Bolting. We produce a complete range of Hydraulic Torque Wrenches for all types of applications: RT Series with Impact Sockets & RTX Series with Hexagonal Ratchet Links.
HYDRAULIC TORQUE WRENCH this is a custom reaction arm for a TITAN TECHNOLOGIES T-10 Hydraulic Torque wrench. No Other competitors Hydraulic wrench could withstand the forces generated by the custom Reaction arm. TITAN TOOLS ARE THE STRONGEST!!! The Proof is in this video!!! Try this with a competitor!!!
The MAMUTH Thin Cutting Frame Saw www.ogden-group.com was developed for cutting solid wood blocks into glueable slats with a minimum of saw kerf waste. The Mamuth is a heavy duty frame saw which has a maximum width of 200 mm and maximum height of 250 mm. TECHNICAL DATA Voltage415V 60 hZ unless otherwise specified Main Motor22 kW (30 HP) Feeding Speed0.3-1.5 m/min Strokes of the Saw Frame250 mm (10) Strokes per minute450 strokes/min Cutting Height Adjustable80 – 250 mm Cutting Width with center guide2 x 25 mm to 90 mm Min. Block Length300 mm Minimum Slat Thickness2.5 mm (depending on cutting height) Cutting Accuracyapprox. + / – 0.3 mm Saw Kerf1.35 mm Saw Blade Life-Stellite Sawsapprox. 10 – 20 hrs. Dust Hood Diameter1 x 120 mm top 1 x 160 mm bottom Machine DimensionsL 3300 mm x W 1000 mm x H 2300 mm Machine Weight4,700 kg or 10340 lbs Machine is equipped with: 1 x Setup frame change device with dial indicator and lineal slide system 2 x Saw frames for cutting 250 mm – 10″ high (unless otherwise specified) 2 x Complete sets of spacers (according to customers size requirements) 10 x Complete sets of Saw Blades and Hoggers (according to customers size requirements) 1 x Precision torque wrench (200 Nm) 1 x Adjustable chip breaker 1 x Air blast system Automatic raise lower of the top feed rollers via photo sensor Digital feed speed indicator Automatic opening of the machine for frame removal Automatic central lubricating system Driven feed rollers top and bottom
Rapid-Torc® is The Expert for Industrial Bolting. We produce a complete range of Hydraulic Torque Wrenches for all types of applications: RT Series with Impact Sockets & RTX Serie with Hexagonal Ratchet Links.